Guide · Homeowners · 3 min read · Updated 17 November 2026
Choosing an Electric Fire for a Media Wall: Sizes and Safety
Short answer
Choose the electric fire before the media wall is designed, because the opening, depth and ventilation are built around it. Inset letterbox fires from 1,000 to 1,800 mm wide are most common, and supply and fit costs £450–£1,500. The fire should run from a fused spur, follow the manufacturer's clearances and sit below the TV with enough gap that heat does not reach the screen.
Types of electric fire used in media walls
Most media walls use an inset letterbox fire, a long, shallow electric fire designed to be recessed into a stud wall. Fronts can be glass, open-fronted or three-sided, and flame effects range from simple LED strips to realistic 3D water-vapour effects. Fuel beds of logs, pebbles or crystals change the look. Wall-hung fires that sit on the surface are an alternative, but they lose the built-in look that most people want from a media wall.
Some fires have the heater above the flames, blowing warm air out of a vent at the top, while others blow from the bottom. The heater position affects where the TV can go and how much space to leave between them.
Sizing the fire to the wall
A fire that is too small for the wall looks lost, while one that is too wide crowds the niches. As a rule of thumb, many designers make the fire roughly the same width as the TV or slightly narrower, and keep it centred under the screen. The table shows common pairings, but the final choice depends on your wall width and taste.
Depth is the other dimension to check early. Inset fires vary from very slim models to deep units with realistic fuel beds, and the deepest fire you are considering sets the minimum depth of the whole media wall. In a small room, a slim fire can save valuable floor space.
| Fire width | Typical wall width | Often paired with |
|---|---|---|
| 1,000 mm | Around 2.2–2.6 m | 50 to 55 inch TV |
| 1,300 mm | Around 2.6–3.0 m | 55 to 65 inch TV |
| 1,500 mm | Around 3.0–3.5 m | 65 to 75 inch TV |
| 1,800 mm | 3.5 m and wider | 75 inch TV and above |
Depth, ventilation and clearances
Every inset fire comes with an installation guide that sets the opening dimensions, the required depth and any ventilation gaps around the fire box. Some fires need air gaps at the top or sides of the opening, some need non-combustible material close to the heater outlet, and some specify a minimum distance to anything above. These instructions must be followed exactly, because they are what the fire's safety testing assumes. A fire squeezed into an opening that is too tight can overheat and cut out repeatedly, or worse.
The gap between the fire and the TV matters too. Warm air rising from a top-vented heater can affect the TV over time, so leave a generous gap, and check both the fire and the TV manufacturers' guidance.
- Build the opening to the fire's installation drawing
- Keep any specified ventilation gaps clear
- Respect clearances to shelves, LEDs and the TV
- Leave access to the fire's controls and isolation
- Never enclose a gas fire in a sealed stud wall
Electrical supply
Electric fires with heaters typically draw up to around 2 kW on full heat, and the flame effect alone uses much less. Installers normally connect the fire to a fused spur, which allows it to be isolated for maintenance without removing it from the wall. The spur is best placed in a niche or near the fire where it can be reached, not behind the fire itself. All work should comply with BS 7671, and new circuits in England and Wales are notifiable under Part P of the Building Regulations unless done by a registered competent person.
Plugging a fire into an extension lead tucked inside the wall is unsafe and should be avoided. A permanent, properly protected supply is the right approach.
Gas fires and media walls
If you already have a gas fire, or want one, the rules change. Any work on a gas appliance must be done by a Gas Safe registered engineer under the Gas Safety (Installation and Use) Regulations 1998, and a gas fire needs its flue and ventilation to remain clear and working. Building a sealed stud wall around a gas fire, or covering its air vents, is dangerous. Most media walls therefore use electric fires, and where an old gas fire is being replaced, a Gas Safe engineer should disconnect and cap the supply before the wall is built.
Features worth paying for
Before ordering, check the fire's opening dimensions, depth, ventilation needs and electrical requirements against the wall design, and keep the installation guide for the installer. Changing the fire model after the wall is framed usually means reworking the opening.
The most useful features are a quiet fan, a heat setting that can be switched off for flame-only use in summer, a thermostat and a remote control or app. Flame-only running uses very little electricity, which is how many people use their media wall fire most of the year. Adjustable flame colours and brightness help match the mood of the room. Check the warranty and whether replacement parts, such as LED strips and remote controls, are available. We supply and fit fires as part of the wall build, so the opening is built to the chosen model from the start.
Questions people also ask
Can I put a TV above an electric fire?
Yes, that is the standard media wall layout, but leave enough space between them. Warm air from a top-vented heater rises towards the TV, so follow the gap recommended by the fire manufacturer and check the TV's operating guidance. Many people use flame-only mode when watching TV, which produces very little heat.
Do media wall electric fires need ventilation?
Some do. Many inset fires require specific air gaps or vents in the opening so the heater can draw in and release air. The installation guide for your model sets out exactly what is needed, and the opening must be built to match. Ignoring this can cause overheating and cut-outs.
How much does it cost to run an electric fire in a media wall?
Flame-only mode uses little electricity, typically a fraction of the heater's rating. With the heater on full, a fire drawing around 2 kW costs the same as any 2 kW heater at your electricity rate. Using the thermostat and lower heat settings keeps running costs down.
Written and checked by the Media Wall Builders team. Read our editorial policy.
More guides
How Much Does a Media Wall Cost in the UK?
A standard media wall up to 3 metres wide, with a TV recess, fire opening and tape-and-fill finish, costs £1,400–£2,600, excluding the fire. Larger…
How Is a Media Wall Built? Step-by-Step Process Explained
A media wall is built by framing a false wall in timber or metal stud in front of the existing wall, running cables and fixing noggins for the TV,…
Media Wall TV Height and Recess Size: How to Get It Right
On a media wall, aim for the centre of the TV to sit roughly at seated eye level, usually around 1 to 1.2 metres from the floor, adjusted for the…
DIY Media Wall vs Professional Build: What You Need to Know
A confident DIYer can frame and board a simple media wall, but most people underestimate the finishing and the electrics. New sockets and spurs must…
Get a free media wall builders quote
Tell us what you need and we'll come back with a clear price.
Request a quote